Working With Marginalized Populations Of The United States

In this internship I expect to gain a further knowledge and understanding of best practices in working with marginalized populations. I also hope to make connections with fellow social workers that share similar passions and values. Population #1: Refugees/Immigrants: Refugees and immigrants have a specific set of needs that differ from other families. Oftentimes they suffer from a lack of resources and do not fully understand the culture that they live in. I would like to work with this population because I have experience in helping refugee/immigrant families succeed in the United States, while helping them to retain their own culture and identity. Though I have some experience working with this population, I would like to learn more about the depth of their needs and the ways that social work as a profession is seeking to fulfill that need. Population #2: Children and Families: Children and families are the foundation of our society and our future. I understand family social work as both tertiary intervention and primary prevention. Issues such as unemployment, abuse, neglect, and lack of housing can put undue stress on family systems. By addressing and helping to alleviate these issues as a tertiary intervention a family can have increased stability in its home life. This strengthened environment can be a primary preventative measure for the children in the home. It can lead to lower levels of incarceration, higher education rates, higher employmentShow MoreRelatedThe 9 / 11 Attack Essay1599 Words   |  7 Pagessupport and keep their family and themselves safe. People like Muslims and Mexicans, whether their immigrants or not, are the ones that are marginalized the most making it hard for them to live a life where they are not looked down at and are not oppressed or discriminated by others. As many of us may know Muslims have been frowned upon in the United States for the reason that there have been various terrorist attacks, the 9/11 attack being one of the major happenings, caused by people from thatRead MoreThe Latino Political Experience : The Electoral Based And The Household Model1580 Words   |  7 Pagesnot designed to benefit minorities, Latinos had to put aside their differences and come together in order to address to economic, political, and social marginalization they faced. Due to restructuring and globalization large segments of the Latino population were excluded from effective economic and political access and participation. As their numbers increased Latinos began to utilize different methods to address the changes in their communities. They used two main methods which reflected two conceptionsRead MoreEnvironmental Justice Issue Of Environmental Discrimination Into The Great Lakes Restoration Initiative1748 Words   |  7 Pagesdevelop a plan of ac tion on your behalf. As you are aware, protecting the Great Lakes is critically important. It is not only the largest source of freshwater in the United States but in the whole world. Indiana, Illinois, Michigan, Minnesota, New York, Ohio, Pennsylvania, and Wisconsin border the Great Lakes, and all of those states use it as a water source for a total of about 10 million people. Since the passing of the Clean Water Act, industries like U.S. Steel Industry have been using the loopholesRead MoreThe American Of The United States Essay1731 Words   |  7 PagesAs demonstrated, women from Central America left their homes to seek employment in the United States for domestic work for a variety of reasons and factors. During the 1960s and 1970s the demographics of migrants from Central America started to shift. Originally men were the primary immigrants to migrate to the United States for jobs in agriculture. However, as the openings in the domestic work industry formed, Central American wo men started to pioneer their own labor migration. An example of thisRead MoreIs Homelessness Not Just A Problem?1714 Words   |  7 Pageseradicated borders in society, creating unique communication opportunities and business ventures worldwide without leaving home is phenomenal. The significance of the advances in technology is the fact that homelessness is not just a problem in the United States, it has global implications. The people that die and are displaced as a result of homelessness is a major challenge to social justice. Through the tenets of the Critical Race Theory, it’s been statistically qualified and quantified that minorityRead MoreAn Awareness Of Counseling And Related Educational Programs1334 Words   |  6 PagesResearch suggests that as of 2012, over one million individuals are living with human immunodeficiency virus (HIV) in the United States (Center for Disease Control and Prevention [CDC], 2015). Additionally, these individuals are more likely to e xperience psychosocial issues such as social stigma and mental health concerns (Barua, Sharma, Basilio, 2013). This supports the notion that most counselors will counsel someone that has a seropositive status (Rose, Sullivan, Hairston, Laux, PawelczakRead MoreThe Little Tokyo Service Center and Language Barrier Assessment2277 Words   |  10 PagesCenter working with mono-lingual Korean seniors. 1st generation monolingual Asian American senior citizens often experience marginalization because of limited resources in addition to language barriers. As a result, monolingual Asian American seniors are constantly experiencing multiple barriers in society, because of the disenfranchisement of people of color. Delgado and Stefancic (2001) describe the stratification of the Eurocentric ideology and values that are embedded in the United States. BecauseRead MoreRacism Without Racists By Eduardo Bonilla Slave849 Words   |  4 PagesFaces of Oppression, were common problem for all Chinese nonimmigrants. Nonimmigrants were not equal to illegal residents. Nonimmigrants meant those who held Visas while studying or working in the U.S. Nonimmigrants had the chances to apply for United States Permanent Resident Cards and then applied for United States citizenships to become Chinese Americans. However, they never get the chanced to be real Americans and enjoy the same rights as Americans did. To change this situation, Chinese nonimmigrantsRead MoreThe Article Child Trafficking Thailand : Prevention And Prosecution Challenges `` By Ross Michael Pink851 Words   |  4 PagesThailand’s Police and Judiciary System, that enables an environment for child trafficking. Despite Thailand being a signatory of the United Nations Convention on the Rights of the Child (CRC 1989), the country fails to comply to Articles 34 ad 35 of the Convention—that State Parties protect children from all forms of sexual exploitation and sexual abuse, and that all State Parties take app ropriate measures to prevent the abduction of, the sale of, or traffic in children for any purpose (Pink, 2013).Read MoreOppression Of Minorities During The Civil Rights Movement871 Words   |  4 Pagesdemonstrated a slow, yet vast amount of success in this marginalized group. Activists endured a long journey toward gaining rights for the community which lead to a modern day civil rights movement for the LGBTQIA community. Although there has been a great amount of successes, non-heterosexual individuals still do not have full equal rights as their heterosexual counterparts. There are still adversities that are being faced in this population that hinder these individuals from thriving. The issue

Manufacturing processes for bicycle frame and golf club Free Essays

string(94) " is not required at all and rather a lug \(figure 3\) is used to fix the two frames together\." Almost every item we use in our everyday life has been manufactured in some way using a series of different techniques. The task set out in this assignment is to look at two everyday objects and discuss the ways in which they have been manufactured and what materials have been used and why these specific manufacturing techniques and materials have been used. We also have to look at other possible techniques and materials that could have been utilized instead and what effect this would have had on the final product. We will write a custom essay sample on Manufacturing processes for bicycle frame and golf club or any similar topic only for you Order Now The two objects that I have decided to investigate are the bicycle frame and the golf club. I have chosen to investigate these two items due to their similarity in materials and manufacturing processes but also their diversity as I will demonstrate in the rest of the report. First I will look at the bicycle frame then the golf club and then finishing with a short conclusion and comparison of the two different objects. 2. BICYLE FRAME The concept of the bicycle was first conceived in the late 18th century in France where an inventor created a wooden hobby horse known as a Celerifere, which had two wheels connected with a beam [1]. From this idea there have been numerous alterations and improvements to every aspect of the design that have led to the invention of the modern bicycle. These include the materials used (wood – alloys – composites), the structural design and the techniques used to manufacture the frame. The design of the modern frame can be seen in figure 1, with the names of the tubes labelled on the picture. Figure 1 – Diagram of modern bicycle frame with all parts named [2] 2.1 Materials Modern bicycle frames can be made from a variety of different materials depending on its application. Standard bicycle frames are usually made from some form of metal alloy such as steel, titanium or aluminium. Steel and titanium alloy frames are generally more popular due to their increased strength over aluminium giving them a longer life. Aluminium alloy is an ideal material in applications where weight must be cut down and the loads placed on the frame are not excessive. The particular compositions of metals within the alloy are constantly being altered to improve weight, rigidity and strength. The strength of the material is particularly important in applications such as mountain biking and downhill racing where the frame comes under considerable loads. The structure of the frame also plays a large part in the loads it can take due to the front and rear triangles that distribute the load throughout the entire frame. In the last two decades the use of composite materials has become more popular, especially in racing bikes due to their increased strength and low weight. These frames are most commonly made with some form of structural fibre such as carbon or glass. Due to the increased strength along the axis of the fibre, single piece frames can be produced giving increased strength in the areas that require it. 2.2 Manufacturing Process Looking primarily at metal alloy frames, there are two main types of tube that can be produced. These are seamless tubes, which are drawn through several stages from a block of metal and the others are known as seamed tubes, which are made from sheet metal rolled into tubes and welded along the length of the tube. Seamless tubes are generally seen as the better alternative due to the fact that they do not have a seam running along their length, which could be a possible stress concentration area. The process for making seamless tubes is as follows: First the metal alloy to be used is annealed to soften it and then hollowed. Once it has been hollowed it is heated once again and then pickled in acid to remove any oxidation layers and then lubricated to prevent any oxidation after the pickling stage. Secondly the hollow is cut to the right dimensions and mitered, a process of shaping the ends of the hollows to fit the contours of the tube to which it is to be attached to. This process is done simply by sawing off the necessary shape of the fit and then filing it down to a smooth finish. Next the tubes go through a cold drawing process to get them to the right gauge by creating a thinner and longer tube. The tube can also be ‘butted’, a process that increases the thickness of the tube at the ends due to the increased stresses located at these points and making the tube thinner near the centre as the stresses are smaller at this location. This process decreases the weight and increases the strength of the frame. The final stage in making the tubes is shaping and tapering them depending on which area of the bike they are to be used in. Once the tubes have all been made, they are joined together to form the frame using either some form of welding if the tubes are made from metal or joined using an adhesive if they are made from composite. The most coming joining method for metal frames is, by far, brazing welding. This process involves placing the tubes together and heating the joints up to create a white flux, cleaning and melting the joint. Next the brazing filler metal is added, usually brass, which melts below the temperature of the joints and flows around them creating an even seal (figure 2). This process is usually done by a machine but some specialist bike makers will still do this manually. This method of welding is preferred to others, such as MIG and TIG welding, as it can be completed at much lower temperatures and so not adversely affect the properties of the material as it may change its structure at high temperatures (i.e. steel). In some frame constructions welding is not required at all and rather a lug (figure 3) is used to fix the two frames together. You read "Manufacturing processes for bicycle frame and golf club" in category "Papers" This allows for easy bike maintenance and tube replacement with little effect on the rest of the frame, unlike its welded counterpart. For composite frames, rather than welding the frame together, which would be ineffective, the joints are glued together using a strong adhesive. The adhesives used are capable of sustaining the same force as effectively, if not better, than welded joints. Figure 2 – Example of braze Figure 3 – Aluminium lug connecting top tube and welding on an L-section [3] seat tube [4] While the joints are still hot enough, the frame is placed into a jig to ensure that all tubes are aligned properly and if not they are oriented to the right position before the metal cools. The frame is then pickled to remove any excess flux and brazing filler and then grinded for a smooth finish Small alignment changes can still be made once the frame has cooled. Finally the frames are taking to be painted to help protect them from oxidation. First the lubricant used to protect them after pickling is cleaned off and then an undercoat is painted onto the frames. After which, a coloured enamel is painted on either by hand or by passing the frame through an electrostatic painting room where the positively charged paint is attracted to the rotating negatively charged frame. Once the frame is finished it is ready for the rest of the bikes components to be added. 3. GOLF CLUB The origins of golf are unclear as many countries had some form of game involving hitting on object with a stick dating as far back as the Roman Empire. Golf as we know it today was popularised in Scotland in the 15th Century where players would use completely wooden clubs to hit a stuffed leather ball. It wasn’t until the introduction of the modern hard rubber golf ball in 1848 [5] that the materials used in the club design were altered. First iron was introduced as a material for club heads, used to strike the ball. Wooden heads were still used for certain shot types. Wooden shafts were still used despite the head material until the early 20th century when the first steel shafts were introduced. In the following years specialised clubs were developed (i.e. sand wedge) and in 1970’s the first composite shafts made from high strength materials were introduced but did not gain popularity straight away due to their apparent decrease in stiffness resulting in flexing. Developments into composite shafts have made them a popular alternative to steel shafts due to their light weight and strength. Figure 4 – Variety of different club heads [7] 3.1 Materials The materials used to manufacture a golf club vary widely depending on the part that is being made such as the grip, shaft and head. The grips can be made of either a moulded synthetic rubber or bound leather, materials with a high coefficient of friction preventing slip. The shaft material can sometimes depend on the application of the club (driver, putter etc.) and are generally made from a stainless steel, titanium or aluminium for metal frames and a carbon/boron fibre reinforced epoxy. The material used for the golf heads can depend a lot on the type of club that it is. For wood type clubs the most popular materials to use are similar to those used for the shafts; stainless steel, titanium and carbon fibre epoxy. Oversized wood heads are often filled with synthetic foam so that the weight is similar to a smaller headed club. It is still possible to purchase wooden heads for the club but these are generally more for aesthetic and traditional purposes than for performance. Irons and wedges generally have heads made from stainless steel, titanium, tungsten, beryllium nickel/copper or a combination of these materials. Putters can be made from a lighter, weaker material such as aluminium due to the low impact forces that they sustain as they travel at slower velocities. 3.2 Manufacturing Process As mentioned previously there are three components to the golf club, the grip, shaft and head. Each can be made using a variety of techniques that depend on the material being used and the preference of the manufacturer. The synthetic rubber grips are made by placing the end of the shaft into a hollow die, the required shape of the grip, and injecting the rubber into the hollow. The mould is then left to harden and the shaft is removed from the mould. Depending on the material the shafts can be created in numerous ways. If the shafts are made from steel or stainless steel then they will be made by a process known as tube drawing. There are several different methods for this process such as rod drawing, fixed mandrel drawing and tube sinking. As these methods are closely related I will only look at the situation where the shafts are made via tube sinking. This process involves pulling the tube part way through a die that has a slightly smaller inner diameter than the tube, causing the tube to neck down in diameter. This is down several times with smaller lengths of the tube. This process helps to reduce the weight of the shaft and increase its strength in the areas of greatest stress (i.e. the shaft/head connection). If the tube is made from a carbon fibre composite a different process can be used. The most common is known as pultrusion where the carbon fibres are fed through a heated die with epoxy resin being fed through at the same time (figure 5). The resin hardens under the heat and forms the shaft. The composite shaft does not need to be necked during its manufacture. The metal club heads are made by a process called investment casting. A die, often made of rubber or metal, is made in two separate halves and has a hollow in the shape of the part to be moulded to allow easy removal once the mould has hardened. Wax is injected into the mould and left to harden. The mould is removed and the process is repeated several times until a collection of moulds have been produced. These moulds are then placed on the stem of a ‘tree’ known as a sprue. The sprue is then invested with liquid slurry and coated in a ceramic powder and left to dry. This process is repeated until the coat is roughly 5-10mm thick. The investment is then placed in a furnace at about 550 – 1100 oC to melt the wax, which is allowed to flow out of an opening in the bottom of the cast. The cast is then fired and preheated and then inverted to allow the molten metal to be poured into the opening of the cast. Once the metal has cooled and hardened the ceramic shell is broken apart and the heads are removed from the tree. The heads are then finished with a heat treatment to harden the surface of the material and then grinded and polished for a clean surface finish. Another possible method of creating the heads is to heat up a stock piece of metal and forge it in a die to produce the part needed (figure 6). The advantage to this method is an increase in strength as the grains follow the flow of the component rather than being broken up due to casting and machining. The disadvantages of this method can be a poor surface finish and the component will usually have to go through several finishing stages to get the finished piece. Figure 5 – Composite shaft being made Figure 6 – Club head made through the  through the process of pultrusion [6] process of forging [6] Once all the parts have been made the shaft needs to be connected to the head. This can be done by a variety of methods such as creating a thread on the end of the shaft and a thread socket in a short tubular protrusion on the head and screwing them together. Another method is to place the shaft into the head socket and drill a hole through both tubes and inserting a metal pin, set with an epoxy resin. If the shaft is made from a carbon fibre composite it is connected to the head using an adhesive, with the advancements in adhesive technologies it is now possible to use an adhesive to bond metal shafts to the heads. The final stage is to check the surface for any blemishes, removing them, and then giving the surface a final polish. 4. CONCLUSION The two most similar components of the two items are the tubes of the bike frame and the shaft of the golf club. Both these components are made from the same general materials such as steel, titanium, aluminium and carbon fibre composite but utilize different methods in their construction. While the bike frame tubes are made from hollowing out lengths of metal and then cold drawing them to achieve the right gauge, golf club shafts are made directly from another method of tube drawing known as tube sinking where the tube is drawing through a die with decreasing diameter, creating a necked tube. Although these methods could be interchanged with each other they usually stick with their own methods as they give the best properties to the components. A similarity in connecting the parts together in both examples was found with the use of an adhesive to bond the carbon fibre tubes of the bike frame and even the metal shaft of the golf club with the head. Although this method could also be implemented with the metal bike frame the common method of joining is still blaze welding as its seen as the most economic method to use. How to cite Manufacturing processes for bicycle frame and golf club, Essays

Tourism in the Philippines free essay sample

Today, tourism clearly offers excellent opportunities for economic growth as shown by the influx of foreign exchange earnings from tourism expenditures. But tourism’s impact is not totally positive. The socio-cultural and environmental impact of tourism must be weighed against its positive economic contribution. Until recently, there had been no measurement of the economic reality of the tourism industry. Its economic importance through the supply side, the capital formation it generates, its value added and its contribution to employment, balance of payments and gross national income. The social impact of tourism notwithstanding, up-to-date, reliable and relevant tourism statistics must be generated. These can help guide the formulation of public policies, promote the importance of the tourism sector, and stimulate recognition of the contribution of private sector tourism operators in the socio-economic development of the nation. The Philippines consists of 7107 islands. Most of the islands are very small. Many of these small islands as well as the bigger islands, have a lot to offer to tourists. We will write a custom essay sample on Tourism in the Philippines or any similar topic specifically for you Do Not WasteYour Time HIRE WRITER Only 13.90 / page There are many possibilities for typical sun, sea and beach holidays and for specific adventure holidays. You can even meet the whale sharks and swim close to them. For tourists who want to discover geographically interesting landscapes or who want to meet mountain tribes, the Philippines has it all! Tropical countries like the Philippines are in many ways attractive for tourists. On the other hand tourists are attractive for a country as the Philippines! For the national government tourists are welcome, because they bring money to the country. Some of that money will go as tax to the national government. Many Philippine businesses, small or big, offer their services to the tourists. A big part of the money that tourists will spend during their stay, will go to these businesses. Last but not least, tourists in the country will bring a lot of possibilities for jobs. Because the total employment in the industrial sector of the Philippines economy is still moderate, the tourist sector is extra important for creating possibilities to have employment for many families. Tourists, Mabuhay!